REGION: LANGUAGE:
My Account Briggs & Stratton My Cart (0)

Fuel Hose Removal & Re-installation Instructions


Share |

Posted In


Fuel Hose Removal & Re-installation Instructions
For DIY Part No. 5414 

FITS ENGINES:
Fits most Briggs and Stratton engines.

1. Run engine until it stops from lack of fuel. Wait until engine cools before performing any maintenance.
2. Using standard pliers, squeeze tabs on hose clamps and slide them away from hose ends.
3. Remove hose from fittings. Beware of residual fuel in hose. Keep old hose to use as a measure for the proper length of new hose.
WARNING
Gasoline and its vapors are extremely flammable and explosive. Fire or explosion can cause severe burns or death.
• If fuel spills, wipe it up immediately.
• Do not attempt to start engine until fuel evaporates.
4. Trim replacement hose to same length as discarded hose.

NOTICE: Trimming hose may leave small burrs or particles which may fall into the hose. Ensure hose is not clogged with dirt or particles before installing. Dirt or particles will clog fuel line or damage engine.

5. Install new clamps onto each end of hose. Install new hose over fittings, and secure with clamps.
6. Upon first use, check for leaks!
WARNING
• If fuel is leaking: Stop engine, and re-secure hose and clamp.
Consult with an Authorized Service Dealer for assistance, if required. 

I have a briggs&stratton 550e series engine. how do i get to the fuel line to replace it ? gas is leaking.

Asked by: annikaj
To locate any information on your engine, you will first need the model type and code. Please see the following link for assistance in locating these numbers: http://bit.ly/17rzznN Once you have this information you can find information on your engine here: http://bit.ly/12pIs1I Select engine as your product type and follow the directions for entering the model type and trim into the search fields.
Answered by: Nicole_BriggsStratton
Date published: 2014-07-02

I have a poulan riding mower and I need to find a view of the hoses and where they go for a briggs & Stratton engine with the serial number 080207ZE49045 I have a broke hose but can't tell if it vac or fuel hose.

Asked by:
You can find the fuel pump diagrams here: http://bit.ly/ZzVRQA where is call out the hoses.
Answered by: Nicole_BriggsStratton
Date published: 2014-08-10

i broke the little plastic square head thing it attached to. where do i find that part?

Asked by: marilin
To locate any information on your engine, you will first need the model type and code. Please see the following FAQ for assistance in locating these numbers: http://bit.ly/17rzznN Once you have this information you can find information on your engine here: http://bit.ly/12pIs1I Select engine as your product type and follow the directions for entering the model type and trim into the search fields.
Answered by: Nicole_BriggsStratton
Date published: 2014-03-27

I have a Briggs & Stratton 5.0hp tiller. MODEL 135202 It will only run for about 10 minutes and then it stuggles to stay running and then it dies. What would cause this. How would I clean the fuel lines and carburetor

Asked by: AvaM
It sounds like dirty fuel lines or carburetor. Here is a link to the FAQ on how to clean this: http://bit.ly/15ihyvq
Answered by: Nicole
Date published: 2014-03-05

I have a B&S Model 422707 Type 152201 Engine. There are three fuel hose connections. I cannot find a hose routing diagram. I have the 3-screw type fuel pump. Can anyone help?

Asked by: Waldo
Here is a link to the fuel pumps and the diagrams on how to set up the hoses: http://bit.ly/ZzVRQA
Answered by: Nicole
Date published: 2014-08-07







Our Starting Promise

Briggs & Stratton Starting Promise

Learn more about our Starting Promise today. 

Learn More »

0 Items in Your Cart

Estimated Price: 0.00